jfet-Biasing

Difference between jfet and bjt:

• Jfet is mostly used in switching operations while bjt is used for linear circuits.
• The voltage gain does not hold good for the fet ,however a bjt gives a fixed voltage gain depending on the configurtion.
• As we all know bjt is a current controlled device whereas fet is a voltage controlled device.The biasing methods of a fet are similr to those discussed in bjt biasing techniques.

Let us get to know them:

1.fixed bias:

The figure below shows the fixed bias configuration for a n type JFET. The circuit used for its dc analysis is shown below.
Applying KVL in the gate to source loop;
-Vgs-Vgg=0
therefore,Vgs=(-Vgg).

Since Vgg is having fixed value Vgs is also having a fixed value and hence the configuration is called as fixed bias.

The drain current Id can be calculated from shockley's equation:

Id=Idss(1-(Vgs/Vp))^2.
The other parameters can be also calculated as:
Vd=Vdd-Id*Rd.

Vgs=Vg-Vs.

and since source is grounded Vs=0.
Hence
Vgs=Vg.

also
Vds=Vd.

2.self bias:

The self bias configuration eliminates the need for two dc supplies.The controlling gate to source voltage is determined by resistor in the source leg.



Vrs=Id*Rs
since Id=Is
Using KVL
-Vgs-Vrs=0
Vgs=-Vrs


Also Id=Idss(1-(Vgs/Vp))^2
On substituting Vgs and solving further we get quadratic equation:
Id^2+K1*Id+K2=0.

which can be solved to find Id.


vds=vdd-Is*RD-Is*Rs
since Id=Is.

3.Voltage divider bias:

The voltage divider biasing configuration is similar to the network we had seen in transistor biasing.
The gate  voltage is dependent on both the resistor R2 and R1 in the network.




Vg=Vdd*(R2/(R2+R1))

Id=(Vg-Vgs)/Rs

Vds=Vdd-Id*Rd-Id*Rs

Since Id=Is.

biasing of the bjt (part 2)

 We Have discussed two varieties of bias connections.we will consider few more bias connections in this post.
a.emitter bias:


In emitter bias configuration the input is applied across the base and the emitter and the output
is taken across the collector and emitter.
Ib=(vee-0.7)/rb+(h+1) re
Ic=h* Ib
Ie=(h+1) Ib
Vce=vcc-Ic*(rc+re)

B.collector feedback bias:
This configuration employs negative feedback to prevent thermal runaway and stabilize the operating point. In this form of biasing, the base resistor ${\displaystyle R_{\text{B}}}$ is connected to the collector instead of connecting it to the DC source ${\displaystyle V_{\text{cc}}}$. So any thermal runaway will induce a voltage drop across the ${\displaystyle R_{\text{C}}}$ resistor that will throttle the transistor's base current.



Vcc=(Ic+Ib) Rc+Ib*Rb+vbe
Ib=(Vcc-vbe)/Rb+(h+1) Rc
Ic=h*Ib
Vce=Vcc-Ic*Rc

C.emitter feed back bias:

The fixed bias circuit is modified by attaching an external resistor to the emitter. This resistor introduces negative feedback that stabilizes the Q-point.
The way feedback controls the bias point is as follows. If V_be is held constant and temperature increases, emitter current increases. However, a larger I_e increases the emitter voltage V_e = I_eR_e, which in turn reduces the voltage V_Rb across the base resistor. A lower base-resistor voltage drop reduces the base current, which results in less collector current because I_c = β I_B. Collector current and emitter current are related by I_c = α I_e with α ≈ 1, so the increase in emitter current with temperature is opposed, and the operating point is kept stable.


Ib=(Vcc-vbe)/(rb+(h+1) re)
Ic=h*Ib
Ie=(h+1)*Ib
Vce=Vcc-(Ic*Rc)-(Ic*Re)

Biasing of the BJT

The transistors and their configurations have been discussed in our previous post.
So let us discuss the two frequently used biasing techniques in this post.

Before we get into the details of the above mentioned techniques,it is important to get an understanding of Q point or quiscient point.If we plot the Vc vs Ic curve we get the load characteristics of the BJT.On the other hand the plot of Ic for different values of Ib is taken.The intersection of these plots gives the Q point.
This analysis is called as load line analysis.


Fixed bias:
When the transistor is connected in fixed bias,the base is common to both input and output and a fixed dc supply is given to the collector and base.
Fixed Bias or Base Bias. In this condition a single power source is applied to the collector and base of the transistor using only two resistors. Applying KVL to the circuit, Thus, by merely changing the value of the resistor the base current can be adjusted to the desired value
The various equations which can be derived for this bias are as below:

Ib=(Vcc-Vbe)/Rb

Ie=Ve/Re

Ic =h Ib

where h is the ac gain.



Voltage divider circuit:



Equations governing this bias are:

Vb=Vcc*R2/((R1)+R2))
Ve=Vb-0.7
Ie=Ve/Re
Ic can be approxiately taken to be equal to Ie.
Ib=Ie/(h+1)
where h is ac gain
Vce=Vcc-Ic(Rc+Re)

simple diode circuits

Earlier we had discussed regarding the diode charactersitics.Diodes when connected in a particular manner can produce different waveforms across the output.We will discuss such diode configurations in this post.

          

1.AND gate using diodes

Above circuit shows an 

AND gate configured using diodes connected in parallel.When the input V is applid such that the anode is at a higher potential than the cathode the diode is forward biased giving an output .Thus the circuit gives a positive output .Even if one of the diodes is reverse biased the output is zero,since the output terminal is grounded.

2 .OR gate using diodes

Above circuit shows an OR gate configured using diodes.

Even if a single input is such that the diode in series with the source is forward biased then the output is in high state .Only when both the inputs are such that the diodes are reverse biased then the output will be zero.

3.Half wave rectifier using diodes

The above circuit shows the configuration of half-wave rectifier using diodes.During the positive half cycle of the input waveform the diode is forward biased and it replicates the input waveform as it is .During the negative half cycle the diode is reverse biased and acts like an open circuit.Thus the output is zero for the negative half cycle of the input waveform.

4.Full wave rectifier using diodes:

If two diodes are connected such that their two cathodes and two anodes are connected back to back then the circuit acts as a full wave rectifier.During the positive half cycle diode d1 conducts while in the negative half cycle diode d2 conducts.The net voltage is the phasor sum of the two voltages and we get a steady curve across the output.

5.Bridge rectifier circuit:

In bridge rectifier circuit four diodes are connected such as shown above.

During the positive half cycle of the ac input the diodes D1 ad D2 are forward biased,while in the negative half cycle diodes D3 and D4 are forward biased.Thus throughout the input cycle the output is maintained steady giving a fully rectified signal.